78.3 F
New York
78.3 F
New York
Monday, August 2, 2021

What is the difference between MMPT& PWM solar Charge controller

- Advertisement -spot_img

#1 MMPT Solar charge Controller

MPPT regulator It is a charge regulator used to regulate the incoming voltage from solar cells and has several advantages over the PWM charging system, as it invests the electrical energy out of the solar energy at full capacity in charging the batteries without the presence of wasted energy.

At the beginning, to understand the topic more, it is necessary to mention the difference between charging using the PWM method and charging using the method of MPPT:

BWM charging regulators only take the voltage required to charge the battery from the solar cell and leave the excess voltage without investment.
PWM charging regulators are cheap compared to MPPT charging regulators.
• Charging regulators of the type PWM are widely used in solar cell systems of less than 2 kilowatts due to the price difference between them and MPPT charging regulators.
• PWM chargers use Pulse Width Modulation technology, thus helping to increase battery life by breaking down sulfate deposits on lead sheets (information needs to be confirmed).

To understand this, it is necessary to give a practical example:

Example 1️⃣:

If we connect a 30-volt solar panel to a PWM-type charg regulator to abattery of a 12-volt type, in this case the charger takes approximately 15 volts from the module and charges the battery with it and leaves the remaining 15 volts from the solar panel without investment.

Whereas, MPPT charg controllers take the necessary voltage to charge the battery and convert the excess voltage into current (via a voltage converter) in order to speed up the battery charging process and more efficiently (reduces the panel voltage at the expense of raising the charging ampere).

Example 2️⃣:

Suppose we have a 30 volt 200 watt solar panel and we want to charge a 12 volt battery with it, since the panel is 30 volts and the capacity is 200 watts then the output current is 6.6 amps (200/30 = 6.6) because the current equals the power divided by the voltage.
In this case, if we connect the board to the PWM charging regulator, it will charge the battery with a voltage of approximately 15 volts and leave the remaining voltage which is also 15 volts.
The charging current in this case will be only 6.6 amps. Thus, the capacity used to charge the battery is equal to 6.6 * 15 = 99 watts only, while if we connect the same previous board to the same previous battery, but this time using an MPPT charger that charges the battery with a voltage of 15 volts and then transforms the remaining voltage of 15 volts into a current, the charging current becomes 13.3 Ampere.

Example 3:

If I had a 150-watt board and I have a 100-amp battery, and I used a PWM-volt regulator (the board is known to be 18 volts) and the voltage needed to charge the battery to the upper limit is 14.6 volts, of course the PWM regulator reduces the charging voltage from 18 volts to 14.6 or 14.4 volts and the ampere of course is the ampere of the board as it is 8.33 amps , That means I will have 3.4 volts of unused excess voltage
(18-14.6 = 3.4v)
But if you use MPPT, this excess voltage will appear as amperes in charging the battery.
The charging amp will be in the case of the MPPT regulator:
150W / 14.6V = 10.27A

Compared with the PWM which gives only 8.33 amperes and thus the performance difference between the two types of solar regulators will be:

10.27 / 8.33 = 1.23

This means a 23% performance difference between the regulators
On the one hand, the panels are connected in series (series) in the MPPT regulator thus providing the cable size, unlike the PWM.

How to convert voltage to current?

There is a general rule in the science of electronics and electricity that says it is impossible to raise the voltage except at the expense of the current and vice versa, so the current cannot be raised except at the expense of the voltage, and this is what MPPT type charging regulators do, as they raise the current at the expense of the voltage, but in both cases the power ( Capacity) remains the same.
Voltage and current are two parts that do not separate, so by changing one of them, the other changes (considering the power is constant).
It is on this base that the voltage is converted to current in MPPT charging regulators

# When to use MPPT and when to use PWM?

# MPPT trucks are often used when:
1) There is a large voltage difference between the solar panel voltage and the battery voltage, thus there is a large energy waste.
2) The system size is large (greater than 2000 or 3000 watts), so raising the current a little helps dispense with purchasing additional solar panels.
3) MPPT is preferred in cold regions because in cold climates the voltage of the panels is increased, and this increase is exploited by the MPPT and turns it into an ampere that charges the batteries.

# PWM trucks are often used in the following situations:
1) The voltage of the solar panel is close to the battery voltage, so there is no big waste of energy.
2) The system size is small (less than 2000 watts).

Disclaimer: This article is for informational purposes only. It is not a direct offer or solicitation of an offer to buy or sell, or a recommendation or endorsement of any products, services, or companies. OTCBBStockNews.com does not provide investment, tax, legal, or accounting advice. Neither the company nor the author is responsible, directly or indirectly, for any damage or loss caused or alleged to be caused by or in connection with the use of or reliance on any content, goods or services mentioned in this article.

- Advertisement -spot_img
Lena Berryhttps://otcbbstocknews.com
Lena Berry is the executive editor of OTC BB Stock News. Apart from managing the large team of writers, you will find her writing about various topics.
spot_img

Latest news

- Advertisement -spot_img

Related news

- Advertisement -spot_img
Subscribe to our newsletter.We never spam.